How To Cut A Brick Wall Without Dust?

How To Cut A Brick Wall Without Dust
How do you cut bricks without dust? You use water to suppress the dust. I have a lot of different machines that are used for cutting, if we have a lot of cuts we set up one of the bench saws, connect a hose and get going.

What is the best tool to cut brick?

Best Brick Saw Contractors and home renovators need to use the proper tools for the job. When you need to cut through masonry, you need a professional brick saw. A brick saw will give you a clean, straight cut without damaging the materials. There are various types of masonry tools that you can use to cut through brick.

  • Diamond saw blades are typically the best option for cutting hard, dense materials such as stone and brick.
  • At SawMaster, we sell a variety of different products, including masonry saws and diamond blades, to make your life easier.
  • What is a Brick Saw? A brick saw is a specialty tool that uses special blades to cut through masonry.

If you use the wrong type of saw for the material, you will end up with chipped materials, crooked cuts, and damaged blades. A high-quality diamond masonry saw blade would last a long time and give you professional results without wasting any product.

A contractor or mason should have a good quality masonry saw on hand for all jobs. At SawMaster, we sell a variety of saws and blades, including out top-of-the-line masonry saw. Features of the SawMaster Masonry Saw Our SawMaster masonry saw is a dry-cutting chop saw for brick and block jobs. It has a large 14-inch blade and strong 3 HP motor that will cut blocks that are up to 5-inches with one pass.

While the saw is extremely powerful, it is lightweight for its class. It weighs only 75 pounds, so you can easily transport it to job sites when necessary. One of the best features of the saw is that you can fit the unit with a wet or dry kit so you can use it in a wide range of situations.

We sell a selection of diamond blades that you can use for the materials that you need to cut. About SawMaster At SawMaster, we are a leading masonry saw company with more than 20 years of experience. We sell a variety of high-quality saws, blades, and accessories. You can count on our products to provide you with excellent, professional results.

We use long-lasting materials, and we put our saws through a rigorous testing process. We ship quickly to the United States from our warehouse in California. Contact SawMaster today to shop for professional brick saws and other specialty products. : Best Brick Saw

What is the best way to cut a brick wall?

5 Methods of Cutting Bricks – The best tools to cut brick include circular saws, angle grinders, reciprocating saws, multi-tools, and manually by using a masonry chisel. Each has its pros and cons:

  • A circular saw fitted with a masonry blade will cut both brick and mortar, producing clean lines, but with a great amount of debris.
  • An angle grinder with a masonry wheel also will cut through both the brick and the mortar and allows for tighter angles. However, debris blow-back is significant.
  • A reciprocating saw with a masonry cutting blade can cut relatively straight lines when the saw is held firmly. But while reciprocating saws allow for plunge cuts in materials like drywall, they don’t work so well for masonry walls.
  • A high-quality multi-tool equipped with a masonry attachment does allow for plunge cuts and can be a good way to get the cut started.
  • Cut brick by hand with a masonry chisel and a drill. This method takes patience, but it offers finer control of the process. Using a masonry chisel is also a great way to cut bricks in half, on an angle, or lengthwise by scoring a line down the brick before applying more pressure.

How do you cut concrete blocks without dust?

How to prevent dust when cutting concrete – How To Cut A Brick Wall Without Dust To cut concrete safely without dust or mess, use a wet diamond blade. If the concrete is dry, dust will be produced as you cut through the material. A diamond blade is best for this task because they produce smoother cuts than most other saws. A wet diamond blade is the best tool for this type of work because the water will trap the concrete dust.

  • By using water to catch dust, the particles fall down and turn into more of a sludgy substance.
  • This prevents concrete dust from becoming airborne and those nearby from inhaling lots of it.
  • The water from a wet cutting diamond blade also helps to cool and lubricate the blade while reducing dust.
  • This stops the saw from overheating while being used.
You might be interested:  Which Components Of Zinc Oxide Eugenol Cement Gives Its Strength?

If you choose to use a dry-cutting blade, like a multi-purpose diamond saw blade, be mindful that they can overheat regularly. You can use a dry-cutting blade with another water source to help prevent it from overheating and reduce dust. One option for a water source is a portable pressurised water tank.

This is usually a small bottle attached to two jets positioned on either side of a guard filled with water. A control valve attached to the bottles allows the operator to control the water supply. You should set your rate of water flow to half a litre per minute at a minimum. This type of addition is often a preferred solution because it is lightweight and portable.

How to cut without dust

Some connect to taps via a hose which keeps the water flowing. Choose a diamond blade size that is larger than the depth of your cut. A depth of 1/8-inch should be cut with a diamond blade that is at least 1/4-inch thick. It is also beneficial to have a concrete saw that has a dust collection system.

Will a multi tool cut brick?

The blade is designed with a universal fitment so it can be used with most brands of multi-tool. Its 32 mm depth range makes it suitable for cutting a channel through brick and thicker materials without becoming too unwieldy for thinner jobs like plasterboard.

Can you cut bricks with an angle grinder?

Q2: What is the easiest way to cut brick? – A: The easiest way to cut brick is by using any high-speed spinning disc tool. In most cases, and angle grinder, circular saw, or a rotary tool fitted with a diamond blade can cut brick. However, you should consider a grinder that matches the size of the brick. These specific tools deliver cleaner, straight, and precise cuts.

What tools can be used to cut a brick by hand?

Materials Needed – You’ll need a cold chisel at least 3/4 inch wide; a broad-bladed chisel, called a brick set, at least 3 inches wide; and a brick hammer.

Can a Dremel tool cut brick?

Product Details. Cut through hard materials, such as marble, concrete, brick, porcelain, ceramics and epoxies, with the Dremel Diamond Wheel. It’s coated with fine diamond particles for tackle these hard materials. The wheel gives you smooth, fine cuts.

How do you cut brick without a wet saw?

Download Article Download Article Bricks are ideal materials for creating walkways and support structures. With a high degree of durability and a wide price range, they can be adapted for use in many situations. But most likely, you’re going to find yourself in situations where you need to cut them.

  1. 1 Draw a line on each side of the brick to create a cutline. Place the brick onto a flat surface. Hold a triangular layout square or ruler on top of the brick and draw the first line in pencil. Rotate the brick and draw the remaining lines until there are lines on each of the four sides of the brick.
    • Be sure that the top and bottom lines and the pair of sides lines are parallel to each other—you need to accurately score along this line.
  2. 2 Score along the cutlines with a 1 inch (2.5 cm) wide cold chisel. Place the brick onto a flat surface and align the sharp edge of your chisel at a 60-degree angle to your cutline. Hammer the chisel gently while moving it along the marked line, alternating the chisel’s angle between pointing downward to the left and downward to the right as you go.
    • Don’t hit the chisel too hard or you might end up breaking off more of the brick than you intend.


  3. 3 Hammer along the groove with a brick-set chisel to break off the unwanted piece. Be sure that the brick is on a flat surface with the side to be cut facing toward you. Place your brick-set chisel into the groove with the straight edge facing you. Tilt the tool’s edge slightly away from you and begin striking the handle firmly with a hammer to break the brick into two pieces.
    • If the brick doesn’t come apart from a firm strike, score around the cutline once more with your chisel. Afterward, try hammering along the groove again.
  4. 4 Remove uneven and excess pieces of brick from the remaining piece. Once the removed piece is out of the way, use your brick-set and hammer to chip off any problematic areas. Look for uneven regions and excess pieces. If the brick is unsteady during this process, place it on a sandbag for support.
    • For uneven spots, a stone carving file is a great tool. When using a file, always drag it along the brick away from you, lift it up, and bring it back. Repeat this process until the spot is even.
  5. Advertisement

  1. 1 Draw a cutline onto the top and bottom of the brick with a pencil. Place a straight edge on top of the brick and mark a horizontal line with a pencil. Afterward, flip it over and do the same to the bottom side. Be sure that both lines are parallel to each other.
    • Since you’re only cutting along the top and bottom of the brick you can skip the sides when you’re drawing lines.
  2. 2 Attach a diamond masonry blade to a circular power saw. Clip a pair of vice grips along the side of the old power saw blade to prevent it from moving. Loosen its center bolt using a wrench and take it off. Now, take off the small rim under the bolt—also known as the flange—and remove the old blade.
    • Attach vice grips to the new blade while retightening the bolt to prevent it from moving.
  3. 3 Grip the handle with your left hand and place your right on the blade’s shield. Practice moving the blade with your left hand and be sure you’re comfortable with the saw. Hold the saw steady with your right hand. Push the blade against the brick to test its stability—it should remain in place.
    • Place a small carpet or rubber mat under your brick if it’s moving around.
  4. 4 Saw along the top line 1 ⁄ 2 inch (1.3 cm) deep. Start by setting the saw blade to a depth of 1 ⁄ 2 inch (1.3 cm). Now, turn on the saw and cut along the penciled line on top of the brick. As you use your left hand to guide the blade, use your right hand to press down on the saw and apply downward pressure to the brick.
    • To adjust the blade depth, release the blade lever by loosening it. Now, move the base of the saw upward to reveal the blade. Stop when only 1 ⁄ 2 inch (1.3 cm) of the blade is exposed and tighten the blade lever to lock the depth in place.
    • Remove the blade from the brick every 30 seconds to maintain a cool blade temperature.
  5. 5 Strike the unwanted end of the brick after placing it on a step. Place the brick onto a step and hold it in place with your non-dominant hand. With your dominant hand, strike the unwanted end of the brick that is not supported by the step with a hammer. The brick should break into 2 pieces cleanly along the score lines.
    • If you can’t find a step, grab the brick with your hands and firmly hit the tip of the unwanted end onto a concrete floor. Just be aware that you’re more likely to create a messy or jagged break using this method.
    • Use a 1 inch (2.5 cm) wide cold chisel and hammer to remove jagged edges. Another alternative is a stone carving file, When using a file, stroke outward along the brick away from you. Afterward, lift the file, bring it back toward you, and repeat the process until the jagged edges are smooth.
  6. Advertisement

Add New Question

  • Question What saw do you use for cutting brick? Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. Masonry Specialist & Founder, GO Masonry LLC Expert Answer
  • Question How do you cut bricks in half? Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. Masonry Specialist & Founder, GO Masonry LLC Expert Answer
  • Question How do you cut brick by hand? Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. Masonry Specialist & Founder, GO Masonry LLC Expert Answer Support wikiHow by unlocking this expert answer. If you’re cutting individual bricks, I recommend using a mason hammer and chisel. Those will allow you to split each brick in half with ease. If you are wanting to cut a lot of bricks, you will want a larger piece of equipment to save you time.

Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit Advertisement

  • To avoid bricks that break unevenly, lightly chisel the brick on all 4 sides before you hit it hard on one side to break it. This way the break will occur on the weakened lines and almost all of your cuts will be perfect.
  • Cutting brick with a hammer alone is best for normal cutting work, such as making closure bricks to go around openings in a wall or finishing corners.


  • Do not hammer the chisel directly to the top or with great force when making the groove. Doing so can cause the brick to split and break unevenly.
  • Be aware that bricks can be cut dry or wet in masonry. Cutting dry bricks may be faster but will create lots of dust. Decrease dust by wetting bricks in water before cutting them. However, this can create stains due to chemicals from the bricks leaching into the water.
  • Always wear gloves and protective goggles when cutting bricks.
  • Wear a dust mask when using a power saw.


  • Brick
  • Pencil
  • Triangular layout square
  • Chisel
  • Brick hammer
  • Brick set
  • Safety goggles
  • Breathing mask
  • Goggles
  • Earplugs
  • Dust mask
  • Gloves
  • Measuring tape
  • Vice grips
  • Pencil
  • Wrench
  • Circular power saw
  • Diamond masonry blade
  • Mallet or hammer

Article Summary X To cut brick with a circular power saw, start by drawing a cut line on the front and back of the brick with a pencil. Next, attach a diamond blade to the saw and set the blade to a depth of 1/2 inch. Then, saw along the front cut line before repeating the process on the back cut line.

How do you clean concrete dust after cutting?

Three good ways for cleaning concrete dust – You can find quite a few tips for concrete dust removal on various forums that you might want to try.1. Tea towel When the cement dust is still quite fresh you can try cleaning the concrete dust with a tea towel. How To Cut A Brick Wall Without Dust 2. Scrapers You can also try scraping tools. You must be very careful not to damage the tiles if you choose this method of concrete dust removal.3. Vinegar mixture Mix equal parts of vinegar and water (50/50). This acidic mixture works well for cleaning concrete dust.

How do you keep dust down when cutting stones?

Applying water to the cutting blade or concrete surface using either a garden hose or plastic bucket appears to be the best method for controlling the dust produced by the blade.

How do you cut concrete cleanly?

Photo 4: Cutting sidewalks and other slabs—with a standard circular saw – Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs, it’s best to cut through the top inch, then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.

What tool would a mason use to cut brick and block?

1 – Masonry Hammer – How To Cut A Brick Wall Without Dust A stonemason’s hammer, also known as a brick hammer, has one flat traditional face and a short or long chisel-shaped blade. It can thus be used to chip off edges or small pieces of stone. The chisel blade can also be used to rapidly cut bricks or cinder blocks.

Do you need a diamond blade to cut brick?

1. Use the right masonry cutting saw blade – All masonry saws require a diamond blade in order to cut through brick, stone, concrete, and other similar materials. However, not all diamond blades are the same! In addition to making sure the blade is the correct size for your masonry cutting saw, you should also try to choose a blade that is specifically indicated for whatever you are cutting.

What is the cleanest way to cut drywall?

How to Cut Out Drywall for Electrical Boxes – It’s important to lay out the location of electrical boxes and rough plumbing carefully.

Draw the cut on the drywall about 1/8-inch larger in all dimensions than the outside of the box. You can skip this step, but for the cleanest cut, score the drywall with a knife. Then, push the jab saw through from the front of the board and cut along the layout lines.

It’s harder than you might think to accurately lay out for cutting electrical boxes. For speed and accuracy, pros make these cuts with a drywall router instead.

Drywall routers are small handheld routers that use 1/8-inch-diameter self-guided bits. The center of the box is marked on the board, and the rough wiring is pushed well back into the box (be sure the circuits are turned off). Then the board is screwed in place with just a few perimeter screws. With the bit set about ½-inch deeper than that drywall thickness, the router is turned on and plunged into the center of the box. The cut is made by cutting to one side until the bit contacts the electrical box, then the bit is carefully hopped over to the outside of the box. Running the router around the box in a counterclockwise direction will cleanly cut it out.

Cuts for doors and windows can also be made with a router. When the router is guided by the inside of the opening, the cut is made in the clockwise direction. Once all the boxes and openings are cut out, the rest of the screws needed to hold the sheet up are driven.

How can I cut wood without dust?

Attach a Vacuum Directly to Your Tools – Whenever you’re sawing, cutting, or sanding wood, a great way to control dust is by cutting it off at the source. The dust won’t be able to make its way into the air if you have something to stop it from getting there.