How To Install Fiber Cement Siding?

How To Install Fiber Cement Siding
Installing fiber-cement siding –

Transfer the wall stud locations to the exterior wall surface. Snap vertical chalk lines to represent the center of each stud. Apply a bead of exterior-grade caulk to the two lower corners of the front wall. Press a length of aluminum Z-channel flashing into the caulk, then fasten the flashing to the wall with 1¼-inch roofing nails. Nail ¼-inch-thick x 1½-inch-wide wood lath to the Z-channel flashing. The lath will bump out the first siding course, creating the proper angle. Cut a length of fiber-cement clapboard siding ¼ inch shorter than the width of the front wall. Score the cut line with a utility knife and snap the siding in two. Apply a vertical bead of caulk at each end of the wall. Set the fiber-cement clapboard siding into place, raise it ¼ inch above the Z-channel flashing, then nail the siding to the wall studs with 1¾-inch roofing nails. The siding acts as a filler strip. Run a vertical bead of caulk along both ends of the clapboard siding. And repeat for each subsequent course. Measure 12 inches up from the bottom edge of the clapboard filler strip, and snap a horizontal chalk line onto the wall. Cut a piece of fiber-cement shingle siding so that its end falls on the center of a wall stud. Hold the shingle siding flush with the chalk line, then fasten it to the wall studs with 1¾-inch roofing nails. Be sure to drive the nails through the filler strip behind the shingle siding. Continue cutting and installing shingle siding up the wall, making sure to overlap all end joints and slots between the shingles. Mark and notch siding to fit around window trim. If necessary, cut individual shingles from a siding panel to fill in beneath a window. Face-nail the shingle pieces with 1½-inch stainless steel nails. Protect the siding with a coat of acrylic latex exterior-grade paint.

How do you attach fiber cement siding?

Fastening Siding – Fiber cement siding can be nailed by hand or with a pneumatic nailer. It can also be attached using corrosion resistant screws.

Use hot-dipped galvanized or stainless steel nails. Nails should penetrate through the sheathing and at least 1″ into studs. Position nails ¾” to 1″ from the edge of the siding. Siding can either be blind nailed at the top or face nailed at the bottom. Use roofing nails for blind nailing and siding nails for face nailing.

Is fiber cement siding hard to install?

Become a Better Installer – Make sure you keep the siding stored flat and covered when not currently in use, and that you pay attention to the installation manual. Fiber cement siding may be a different material than wood or vinyl, but a good installation is not difficult nor time-consuming.

Follow these steps and review the video above to ensure that you know the correct procedure for installing fiber cement siding. With a little attention to detail, you’ll make sure that your fiber cement siding will last for decades to come. Install fiber cement siding today, to start siding better homes.

: How to Install Fiber Cement Siding

What type of nails should be used to attach fiber cement siding?

Fiber Cement Siding Nails: Essential Hardware for Installation Fiber cement siding is a super-strong exterior option for a home that provides exceptional protection from the elements. It is long-lasting and requires very little maintenance. As is often the case with any building material, proper installation is key for fiber cement to reach its full potential and protect the home properly. Unlike natural wood, vinyl, and other old-fashioned siding materials, fiber cement delivers a superior level of strength that keeps damage and deterioration to a minimum. Traditional building materials may chip, peel, fade, and show serious signs of weather damage, but fiber cement is able to maintain its original allure without much effort at all. First off, let’s discuss technique. Some homeowners may be worried that nailing in the siding boards by hand may not be as effective as using a nail gun, while others may assume that a nail gun will send the nails too deep into the siding. The good news is that fiber cement siding can be properly installed using either of these two techniques, so it really comes down to personal preference.

  • Each technique has certain pros and cons.
  • For example, hand nailing can take a much longer time than using a nail gun.
  • However, a nail gun can be intimidating for a homeowner without much experience, thus making hand nailing a safer option.
  • Both of these techniques can get the job done correctly.
  • What’s really important is that the nails are driven cleanly and perpendicular to the surface.

It’s essential to avoid driving the nails at an angle, since it can compromise the long-term potential of the fiber cement siding. Galvanized or stainless steel 6D and 8D nails are typically considered the best nails for fiber cement siding because they are the appropriate size and offer reliable durability. It is advisable to avoid using electro-galvanized nails, and highly recommended to opt for corrosion-resistant, hot-dipped galvanized nails, if possible.

The length of the siding nails really depends on the thickness of the planks. For example, Allura shake has a thickness of ¼-inch, while Allura panels and lap each have a thickness of 5/16-inch. Pay attention to the thickness of your fiber cement siding, because it may affect the ideal nail length for your particular project.

Fiber cement nails should be chosen so that they are able to penetrate the solid wood by at least 1 ¼-inches deep. It can also be smart to consider the finished look of the fiber cement siding nails. Especially in noticeable areas like siding, it can be a good idea to ensure that the nail heads match the exterior flawlessly. Fiber cement siding is often chosen because of its superior strength and long-lasting beauty. Allura offers a wide variety of fiber cement siding styles, including lap, shake and smooth architectural panels, providing homeowners and designers with an abundance of design opportunities.

  1. No matter which style catches your eye, you can be confident in your choice, because Allura fiber cement siding comes with a 30-year Transferable Limited Product Warranty that speaks to its durability.
  2. Allura also offers fiber cement trim, beadboard, and soffit, so you can outfit the entire home with a durable exterior material that looks great and matches perfectly.

With 25 colors to choose from, it’s fun and easy to find your own unique options to beautify the home. Go bold with a vibrant color or keep it classy with a natural, wood-style look. There are so many ways to mix and match Allura’s fiber cement products to create the home of your dreams.

Can I install Hardie siding myself?

It’s Heavy – Some homeowners assume that if they’ve installed vinyl siding, they can install fiber cement siding too. It can’t be that different, right? Actually, Hardie siding is nearly five times thicker than vinyl siding and weighs almost two and a half pounds per square foot.

Should I predrill fiber cement siding?

Nailing Basics – Fiberboard cement siding can be hand-nailed, but because it’s so much harder and more brittle than wood, you have to predrill holes near any edge. You can save yourself a bunch of time by using a pneumatic coil siding nail gun. Unfortunately, a siding gun will set you back twice as much as a 15-gauge trim gun, and it’s only half as versatile, so if installing fiber cement isn’t your full-time gig, you may want to rent one (about $110 a week).

You might be interested:  Maximum Percentage Of Which Species Is Present In Portland Cement?

Use 6d or 8d galvanized or stainless siding nails and install a single nail about 1-in. down from the top edge at each stud, no more than 16 in. apart. n Nail lengths should be chosen so they penetrate a minimum of 1-1/4 in. into the solid wood (wood sheathings like OSB and plywood count toward the 1-1/4 in., but “soft” sheathings like fiber board and foam don’t). Don’t drive nails into the siding at an angle. Fastener heads should be snugged up against the siding, not driven into the surface. The end of each plank making up a butt joint needs to be fastened to a stud. Nail butt joints last. That way you can tweak the ends of each plank so the bottom edges line up perfectly.

Do I need house wrap behind Hardie siding?

1. HardieWrapⓇ Weather Barrier – While fiber cement siding is already waterproof, James Hardie recommends applying their nonwoven synthetic house wrap beneath your siding as that final line of defense if your siding should fail, and so do we. Ⓡ is engineered for the two of the most challenging climates in the United States ; one wrap is designed for cold/wet climates with a perm rating of 25, and another specially designed for hot/humid climates with 15 perm.

  • HardieWrapⓇ UV rating is 180 days.
  • HardieWrapⓇ is 11-mil thick (thicker than other brands) and tear-resistant.
  • HardieWrapⓇ is surfactant resistant.
  • HardieWrapⓇ is rain-resistant with a water hold-out rate of 325 mm.
  • HardieWrapⓇ has 15 perms and 25 perms, respectively.
  • HardieWrapⓇ is wind and cold-resistant for improved energy efficiency.
  • HardieWrapⓇ is a semi-transparent nonwoven, non-perforated polyolefin product.
  • HardieWrapⓇ has a 10-year warranty.

As the #1 fiber cement siding ma nufacturer in North America, their house wrap is equally exceptional. At 11 mil, HardieWrapⓇ is thicker and stronger than other products and contains a patented MicroTech coating that provides an impressive balance between water resistance and vapor permeability.

  1. It is semi-transparent, so your siding contractor can see the boards and studs behind it for easy installation.
  2. Although it is not as UV-resistant as other house wraps, HardieWrapⓇ is designed to go behind fiber cement siding, which provides exceptional UV protection.
  3. So the only exposure this wrap receives is before and during siding installation.

As a premium house wrap product, HardieW rap is more expensive than some other nonwoven synthetic weather barriers, but it’s a small price to pay to protect your home. Wrap Plus is a non-perforated, non-woven polyolefin product with a semi-permeable membrane.

  • Barricade® Wrap Plus UV rating is 9 months versus the 6-month standard.
  • Barricade® Wrap Plus is surfactant-resistant.
  • Barricade® Wrap Plus is cold-resistant.
  • Barricade® Wrap Plus is rain-resistant with a hold-out rate of 325mm.
  • Barricade® Wrap Plus has a tensile strength (ASTM D-5034) of 59 lbs/inch MD, 51 lbs/inch CD, protecting it against wind damage, construction errors, etc.
  • Barricade® Wrap Plus has 16 US Perms.
  • Barricade® Wrap Plus is a semi-transparent house wrap, which allows a view of the studs and sheathing surface and straightforward application.

Ⓡ is a DupontTM product made of nonwoven, non-perforated polyethylene fibers fused together to create a tough, breathable web with tiny pores that resist water and air penetration. You can apply it to an open stud construction such as porch enclosures, which can save you material costs.

  • TyvekⓇ HomeWrapⓇ is more susceptible to damage due to high winds and moisture.
  • TyvekⓇ HomeWrapⓇ is only UV-resistant for up to 4 months.
  • TyvekⓇ HomeWrapⓇ is not transparent, which makes application more difficult.
  • TyvekⓇ HomeWrapⓇ is not surfactant-resistant.
  • TyvekⓇ HomeWrapⓇ has a perm rating of 56, which is a great deal higher than what you want.

Should you caulk fiber cement siding?

Caulking Fiber Cement Siding Like a Pro: How To Guide Fiber cement siding is already well-equipped to deal with the elements, and adding caulk can be a smart way to seal off potential gaps near windows, corners, and doors. Caulking fiber cement siding involves a slightly different process than caulking wood, so it is important to become familiar with the steps involved. As with most building projects, proper installation is absolutely key for the product to perform its best. It also helps to work with a material that is already crafted for better strength and durability. Take a look at the advantages of working with fiber cement siding and learn the steps involved with caulking fiber cement siding correctly. Traditionally, the main purpose of caulk is to close up gaps in the siding so that moisture cannot seep in beneath and create long-term damage. Caulk is used for lots of different siding materials. For many of the traditional building materials, like wood, caulk is absolutely vital.

  1. This is because most wood siding is not capable of holding up on its own.
  2. Moisture can cause wood siding to warp, rot, and weaken, so sealing up gaps with caulk is absolutely essential to ensure a long product lifespan.
  3. When it comes to caulking fiber cement siding, this extra step can certainly help strengthen the siding against moisture.

Because of its unique composition of water, sand, cellulose fibers, and cement, fiber cement is one of the strongest siding materials around. It is already built to be moisture-resistant and weather-resistant which makes it a great choice for durable, long-lasting exteriors.

Does fiber cement siding need an air gap?

Siding & Best Practices for Moisture Rainscreen Solutions forSiding and Shingles The durability, superior appearance, and added value of fiber cement sidings like makes them a popular choice of builders and designers. The leading manufacturers recognize that fiber cement siding lasts longer and resists moisture problems when installed over a predictable, rigid rainscreen air gap.

Natural cedar siding’s unique durability, natural aging and warm aesthetic have been recognized for centuries. While cedar’s appeal is unchanging, the rest of the wall assembly has changed drastically with the introduction of plastic WRBs, air sealing and increased insulation that have altered the walls ability to dry out.

Naturally occurring surfactants in real wood siding compromise the water repellency of many WRBs, allowing incidental water to become entrapped in the wall system without the ability to dry out, leading to damage to the sheathing and wall components.

Can I use a roofing nailer for fiber cement siding?

5. Properly Nail off The Siding – You can shoot Hardie siding on with air powered nailers or use hand driven roofing nails to attach siding to the home or structure. The nails can be ringed- shanked or smooth just make sure you are hitting the studs in the wall.

Place a nail in every stud especially is they are 24″ on center and ensure that nails are between 3/4″ to 1″ below the top of the piece of siding. Nails drive in too high won’t hold as won’t nails that are over driven. Drive nails flush with face of hardie plank but don’t counter sink nail. Our Crews prefer 1 3/4 ” smooth shank roofing nails for Hardie installation.

If we do make a mistake and have to move a piece the smooth shanks are removable unlike a ring-shank nail. : Avoid Common Mistakes When Installing Hardie Siding

Do you nail the bottom of Hardie siding?

What nails do you use for Hardie siding? – For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency.

Can you use screws instead of nails for siding?

Screw fasteners can be used if the screws do not restrict the normal expansion and contraction movement of the vinyl siding panel on the wall. Screws must be centered in the slot with approximately 1/32′ (0.8mm) space between the screw head and the vinyl.

Should I nail or screw Hardie board?

James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.

Do you need a vapor barrier with Hardie board?

Integrated System – The wise folks at James Hardie designed a complete system to ensure your house is snug, cozy, and climate-controlled. Some manufacturers make siding. Some make vapor barriers. Few manufacturers work from the sheathing outward to design an integrated system for protecting your home. James Hardie does, with these fine products:

You might be interested:  How To Use Safety Belt In Construction?

Weather Barrier — James Hardie HardieWrap® weather barrier gives your Des Moines-area home breathability and water resistance. It keeps the space between exterior and interior walls dry. It helps prevent mildew, mold, and energy loss too. Pro-Flashing — HardieWrap® Pro-Flashing, a self-adhesive butyl rubber that peels and sticks around windows and doors, prevents water invasion and air infiltration. It self-seals around fasteners driven through it. Flex Flashing — HardieWrap® Flex Flashing stretches easily and seals around hard-to-fit shapes like custom, bay, or bow windows and door sills. Flex Flashing prevents water and air from entering your home. Seam Tape — The perfect adhesive for Weather Barrier and Flex Flashing, HardieWrap® Seam Tape keeps your home’s building envelope impervious to air and water, even at the seams.

Depending on your local building authority having jurisdiction (the AHJ) over your building codes, vapor barriers are almost always required, whether your builder uses James Hardie products or some other, inferior product. Rolled out vertically and adhered to your home’s sheathing, this vapor barrier is water-resistant, the same way a shingle roof is.

  • It still allows water molecules in a gas state to move out from the sheathing and into the atmosphere.
  • It allows a limited transfer of gaseous water molecules to move from the atmosphere into the sheathing.
  • It prevents liquid water from ruining the sheathing.
  • The water-resistant barrier is the foundation for whatever siding you and your builder or remodeler select.

As part of the James Hardie integrated system of materials, HardieWrap® forms the perfect complement to HardiePlank siding expertly installed by your local contractor,

Do you need plywood under Hardie board siding?

Storage and Care for Cement Siding – Fiber cement siding should be kept covered while not been installed on a clean, flat and leveled surface. The siding must be protected from direct exposure to weather that could damage the cement siding before it is installed. If you need to move siding pieces, be sure to carry them by their narrow edge and support it when you cut larger pieces.

What is the lifespan of fiber cement siding?

2. Siding Materials and Their Lifespan – The lifespan of siding also varies by its material. Generally, quality vinyl siding can last 20-40 years, depending on its specific quality and the climate. Fiber cement siding, on the other hand, offers high durability and can last as long as 50 years.

What is the difference between Hardie board and fiber cement?

Complete Comparison Guide: Fiber Cement or Hardiplank vs. Vinyl Siding By Home Advisor Protecting your home’s exterior needs a sturdy material that resists common outdoor threats like pests, extreme temperatures and harsh weather. Two popular materials for siding are fiber cement, also called HardiePlank, and vinyl.

  • Which one is right for your next project, and how do they compare to each other? What is Fiber Cement? Fiber cement is a blend of cellulose fibers, sand and cement.
  • When it’s manufactured for siding, it resembles natural materials like wood and stone.
  • It’s known for durability, affordability and for being available in a variety of forms.

HardiePlank / Hardie Board vs. Fiber Cement The James Hardie brand produces high-quality fiber cement siding products, often called Hardie Board or HardiePlank. These terms are often interchanged with fiber cement. However, these brand name James Hardie products typically cost more than lower grade siding.

To find out more, check out the, What is Vinyl Siding? Vinyl is made of PVC, or polyvinyl chloride, which is the same material used in luxury vinyl floors. It can look like cedar, stone or tile without the added costs and maintenance associated with organic materials. It can come in shingles, vertical or horizontal planks, and faux log.

Horizontal siding is popular. An insulated version is available and can guard your home against extreme temperatures to make it more energy-efficient. To learn more about this material, explore the, Siding Comparison – Which Is Better for Your Home? Fiber cement and vinyl are both synthetic materials and easier to manage than organic options like wood, shingles or logs.

  • Types & Styles
  • Fiber Cement
  • · This material can resemble stone, wood lap boards, cedar shingles, wood shake siding, logs, and more.
  • · Its premium thickness produces deeply embossed products that look like wood.
  • Vinyl
  • · It can imitate materials like wood shingles, lap boards, logs, and stone.
  • · The styles are just as varied as fiber cement.
  • · However, it falls short when imitating wood because it isn’t as thick.
  • · Lack of depth makes its stone replicas less textured.
  • Colors & Painting
  • Both materials come in an endless variety of colors like light blues, dark ash, bright greens and bold reds.

If the product doesn’t initially come in the color you’re looking for, you can paint both. The falls between $1,700-$4,000. Select a siding that’s already the color you want to save money.

  1. Fiber Cement
  2. · Needs a coat of paint every 5-10 years to keep its luster.
  3. · To save you time for the first few years, buy pre-painted products.
  4. Vinyl
  5. · Doesn’t need paint unless you want to change the color.
  6. · If you bought pre-painted material, repaint it every 5 to 10 years in fair weather and with acrylic and/or urethane paints.

· The paint’s color should be lighter than the current color. Darker paints can absorb the sun’s heat and trap it into the siding, causing it to warp. Cost Comparison Which material is better for your budget? For more information on these prices, see our guide and guide. Fiber Cement · $0.70- $5.25 per square foot.

  • · It varies in price due to the difference in quality between brands and manufacturing methods.
  • · Hardie Board falls on the higher end of this spectrum, usually hovering around the $5 per square foot range.
  • · Overall, it costs more after installation due to the extra labor involved.
  • Vinyl

· $3.00- $6.00 per square foot, with the typical choice costing around $3.00-$4.00 per square foot. · Installation is simpler and less cumbersome, making the total cost after labor more affordable. Which is Best? The right material for you will depend on a variety of factors.

  1. · Budget
  2. · Values (environment, sustainability, etc.)
  3. · Climate & weather patterns in your area
  4. · How often you expect to perform maintenance and repair tasks
  5. · Your home’s look and which siding complements it
  6. Fiber Cement/Hardie Board is Better For
  7. · Durability
  8. · Longevity
  9. · Eco-Friendliness
  10. · Thickness
  11. · Types and Styles
  12. Vinyl is Better For
  13. · Cost
  14. · Maintenance and Cleaning
  15. · Repairs
  16. · Insulation
  17. · DIY Installation
  18. · Painting
  19. Want to learn more? View the full article

: Complete Comparison Guide: Fiber Cement or Hardiplank vs. Vinyl Siding By Home Advisor

Does fiber cement siding increase home value?

Is fiber cement siding worth it and does it increase value of a home? The siding of homes here in the Greater Boston area has undergone many changes over the years – we have gone from wood to vinyl siding and now fiber cement is an extremely popular option.

In fact, fiber cement has been declared by some as the best choice for home siding. However, not everyone is sold on this material and there are still a lot of doubts about it. After all, is fiber cement siding worth the hype? The first step to understanding fiber cement siding is to understand some of the advantages of using it in place of other siding materials.

Is fiber cement siding better than vinyl siding? There are several advantages fiber cement has over vinyl siding, but the most important is that it is fire-resistant. Modern homes are predominantly constructed with vinyl siding, which is both affordable and durable.

However, with the increased risk of wildfires in the United States more and more people are choosing fiber cement siding as a natural, yet aesthetically pleasing, fire-resistant alternative. Vinyl siding has been shown to burn very rapidly, whereas fiber cement will not melt or crack when exposed to high heat sources.

Is fiber cement siding better than wood siding? When it comes to longevity and durability fiber cement siding has many significant advantages over wood siding. Don’t get us wrong, wood siding can last a while with proper maintenance, but being a home owner is easier when your home has siding that is as maintenance free as possible.

  1. Fiber cement is virtually maintenance free, but just because its strong does not mean an occasional pressure wash can hurt.
  2. Wood siding is more costly to maintain than fiber cement, as wood is more susceptible to mold growth and insect activity because wood tends to rot faster than cement, which means that pests can infest this type of wood much more quickly, that means wood siding needs to be painted or stained often to prevent future issues.
You might be interested:  What Is The Difference Between Red Brick And Cement Brick?

With fiber cement though, you won’t have to worry about any pests. Not to mention fiber cement tends to be less expensive than traditional wood-based products.60% of consumers believe that their home’s appearance has a direct impact on its value. A home’s appearance is one of the most significant contributors to its value.

  • The National Association of Home Builders (NAHB) recognizes the superior appearance and energy efficiency of fiber cement siding.
  • It is estimated that fiber cement siding will add 10-15% to the value of homes and is highly sought after by home buyers or real estate appraisers.
  • Think about it—great curb appeal can chase away all the wrong potential buyers or attract just the right homebuyer.

Fiber cement siding looks like real wood but never needs to be painted, and it lasts so much longer on your house. How To Install Fiber Cement Siding Who makes the best fiber cement siding? Some of the most common fiber cement siding brands include: James Hardie, CertainTeed and Alside, all of which are offered by Franca Services. These brands offer a wide variety of different finishes and profiles, so you are bound to find something that fits your tastes. James Hardie Fiber Cement Siding James Hardie fiber cement siding has long been America’s #1 exterior siding choice and is designed to resist fading, cracking and rotting. For a beautiful, protective finish, look no further than James Hardie siding, which comes with a 50-year warranty—the best in the industry.

  1. It is also one of the only siding options that can be customized to complement your home’s style, from a variety of colors and textures that fit seamlessly within your community.
  2. Thanks to this unique product, you can enjoy siding that’s durable enough to last for decades, yet beautiful enough to make your house a showpiece on the block.

There are many options for adding new style and value to your home, but few offer as many benefits as durable as James Hardie fiber cement siding.

With so many benefits that make fiber cement siding better than traditional siding, why settle for anything less?

TL ; DR: Is Fiber Cement Siding Worth It? Yes. Fiber cement siding is a great investment and is worth it! if installed correctly.Fiber cement siding is a traditional material that has been tried and tested for centuries. It will increase the value of your home and protect your family from the elements.To make sure it is installed correctly, hire contractors that are skilled installing fiber cement siding.

  • We can think of 1 contractor in your area that we would recommend for your siding installation, but we are biased.Our customers are saying: “After we completed an addition, we hired Franca services to replace our old chipped wood siding and trim with hardie plank siding and PVC trim.
  • Our house is old and 3 stories so there are a lot of angles and unique spots.

Franca came in and did a tremendous job. We did this work from Jan-Feb, the team was here every day at 630am before it was bright out and left when it got dark, they worked through brutally cold days and the end result was amazing. If you’re considering using them, don’t have any doubts, they’re the team to trust.” – Pat Henderson Are you thinking of going with Fiber Cement Siding? with us today, and make the first step into a better home tomorrow.

What kind of primer do you use on fiber cement board?

Stucco and masonry – The trick with repainting stucco and masonry is to powerwash or clean the loose powdery surface well enough without destroying it. New stucco always should be primed or conditioned for optimal results. Since pH levels can be a concern with new stucco, make sure the primer can be applied to surfaces with a high pH level.

  1. This will minimize efflorescence problems later on.
  2. You’ll get maximum performance from Sherwin-Williams Loxon Masonry Primer.
  3. For the topcoat, use two coats of SuperPaint or one coat of Duration.
  4. The condition of the substrate is critical when repainting.
  5. Stucco cracks will telegraph through the topcoat and should be repaired with patches and sealants prior to repainting.

Repaint the substrate with SuperPaint or Duration. If the job calls for waterproof protection, go with an elastomeric coating such as Sherwin-Williams ConFlex XL High Build Coating, which also can cover and hide hairline cracks. Brick should be allowed to weather for at least a year and then wire brushed to remove efflorescence.

Which side of fiber cement board faces out?

Screw the board in place – Keep screws 1 in. away from the edges. Cement board has a smooth side and a rough side. Face the rough side out if you will be using thin-set mortar adhesive to install the tile but the smooth side out if you will be using latex mastic. Family Handyman Step 9

Can fiber cement siding touch the ground?

How To Install Fiber Cement Siding There’s an ARTISTRY to installing Exterior SIDING ! #1) Do your homework. There’s an Artistry to install Exterior Fiber Cement Siding ! #2) Research companies who produce Fiber Cement. – Pinterest is a great source for images as is Houzz, Google searches for photographs and companies who provide pre-finished Fiber Cement Siding should be easy to find.

  1. Ask questions regarding their materials.
  2. How long have they been in business?
  3. Do they have a list of customers who you may call?
  4. Are there homes for you to drive by?
  5. Do they offer samples of their products?

#3) Research Warranties closely on material and installation. #4) Research pre-finishers coating warranties. Keep in mind the following:

  • Fiber Cement – is just that – it’s Cement.
  • ALL SIDES MUST BE SEALED – that’s why PREFINISHED is the best !
  • Research pre-finishing companies or take your time and make sure the Painter or Installer paints ALL SIDES to reduce moisture damage.
  • Once material has been received from the Pre-finishing company, make sure it’s covered and kept in a dry place until it’s installed. And as said above – make sure it remains dry, all edges and sides are covered.
  • Use matching caulk and touch up paint when and where needed.
  • Use protective eye-wear and a mask when cutting.
  • Fiber Cement should NOT touch the ground. Install it on a stone wall – brick wall, or a barrier wall that provides protection from the wet ground or a wet surface.
  • Maintenance is as simple as lightly spray washing.

See for yourself. Installed properly – it looks AMAZINGLY like REAL WOOD – that’s the Artistry and it lasts for at 15 years or more before another coat needs to be applied. For more information regarding our prefinished Fiber Cement Siding, contact us through our website or call us at (800) 948-4349, the Artistry of installation

Do you nail or screw Hardie siding?

James Hardie prefers and recommends installation of HardiePlank® lap siding by the blind nailing technique, such that fasteners are hidden by the course above. Fasteners shall be installed between 1 in. and 3/4 in. from the top edge and no closer than 3/8 in.

What is the best way to fasten Hardie board siding?

What nails do you use for Hardie siding? – For Hardie siding, it’s recommended to use stainless steel or hot-dipped galvanized nails. You can either nail by hand or use a pneumatic nailer. However, it’s best to use a pneumatic nailer for speed and consistency.

Can you screw on fibre cement?

Needle point design for quick and easy installationSuperior trade qualityCountersunk rib head for flush finishZinc Alloy 3 to conform to AS3566 Class 3Underhead cutter on the countersunk rib head breaks up the cement sheet as the head embeds into the sheeting

Buildex® Fibre Cement Screws are designed for fixing fibre cement sheeting (6-12mm) to soft timber or light gauge steel studs. Typical applications include eaves, fascia, wet areas, ceilings, interior walling and cladding.