Step 4: Cleaning the Fan, and Reapplying Thermal Paste. – The fan, now exposed, can easily be cleaned. I cleaned mine just by blowing it out. It wasn’t very dirty though. ( You could also blow it out by spraying compressed air in through the holes, but what fun is that? ) Be sure to get all the dust off, and while your at it, make sure you clear all the dust out of the fins on the heatsink.

1. Note: When putting the heatsink back on, be sure to run the fan wire down the side of the plastic housing, and out the gap in the sink.) – To start putting it back together.
2. A good thing to do is take thermal paste that is still good, or new stuff if you’d prefer, and spread it nice and evenly over the parts that need to contact the heatsink.

I found LOTS of extra pushed out of the edges, so I simply dragged it back to the center and spread it around. A small screwdriver or toothpick works well for this. When your done, stand the side of the case nice and close to the psu so you can PLUG IN THE FAN WIRE, then carefully press the case back on.

Can you open Xbox 360 power brick?

YouTuber xCrAnKsHoTx teaches you how to take a apart an Xbox 360 power supply, aka power brick, in order to clean it. This could help prevent any red light issues, or overheating in the long run, so it’s good to do as maintenance every year or two to remove all the dust in there. You start by taking out the small rubber feet at the bottom of the power supply. Use a drill to make holes in the plastic caps covering the screws. Then use a screwdriver to remove them on all sides. (You can also pry them off with a knife if you want.) Then pull on each side to get the power supply open. Inside you will find white looking cream, which is electrical grease. Remove the screws on the pieces of metal inside. The fan has another plastic cover on top so remove that as well. The fan itself has only two screws that you need to take out. Finally, you can blow on it or use a brush to clean it. Want to master Microsoft Excel and take your work-from-home job prospects to the next level? Jump-start your career with our Premium A-to-Z Microsoft Excel Training Bundle from the new Gadget Hacks Shop and get lifetime access to more than 40 hours of Basic to Advanced instruction on functions, formula, tools, and more. Buy Now (97% off) > Other worthwhile deals to check out:

97% off The Ultimate 2021 White Hat Hacker Certification Bundle 98% off The 2021 Accounting Mastery Bootcamp Bundle 99% off The 2021 All-in-One Data Scientist Mega Bundle 59% off XSplit VCam: Lifetime Subscription (Windows) 98% off The 2021 Premium Learn To Code Certification Bundle 62% off MindMaster Mind Mapping Software: Perpetual License 41% off NetSpot Home Wi-Fi Analyzer: Lifetime Upgrades

How do I fix my Xbox 360 power brick?

Unplug the power supply from the console and the wall outlet. Let the power supply cool for 30 minutes. Make sure the power supply is in a well-ventilated space, and the ventilation openings on the power supply are not covered. Reconnect the power supply to your console and plug it back into the wall outlet.

How do you clean a Xbox 360 power supply?

Introduction: Disassembling and Cleaning Xbox-360 Power Supply ( Brick ) – In this Instructable I’ll show you how to properly dissassemble your ( or somebody else’s 😛 ) Xbox 360 PSU. If all you want to do is get rid of the dust in it, I would simply recommend blowing compressed air through the vent holes.

Why is my Xbox 360 power brick making noise?

To provide sufficient cooling, the Xbox 360 external power supply uses a built-in fan to blow air through the PSU. When you press the power button to start your Xbox 360 console, the PSU fan starts. Typically, the PSU fan makes a ‘whirring’ noise.

Can an Xbox 360 work without a power supply?

It needs power. The power brick provides power of different voltages on different pins, so you’d need to supply the correct voltage to each pin. This also varies across the different models of Xbox360 which used different power bricks.

What screwdriver do I need to open Xbox 360?

Step 1: Parts Needed – Torx T8 & T10 Screwdrivers – The console is held together with Torx screws, these screwdrivers are easy to find and quite cheap. If you are hoping to open a Xbox 360 controller, you will need a Security Torx T8H. The best ones I’ve found are from Llamma’s Tool Section,

Small Flathead Screwdrivers/Paper Clips – Used to hold open the friction locks of the 360 front cover. You can also use paper clips if you desire.360 Opening Tool ($7 – Optional) – This is a specialty part used to pop the rear locks and remove the heating grills. This is worth the $7 pricetag found at Llamma’s tools if you open systems repeatedly.

Another option for an opening tool is a small flat-head screwdriver, you will have to pop each friction lock one at a time, but almost everybody has a satisfactory screwdriver. Removing the shell gets frustrating and tiresome if you open lots of boxes, but if you don’t feel like spending $7+s/h and waiting a week for a tool you will only use twice, don’t bother with the Llamma tool.

Can you bypass Xbox 360 power supply?

To those wondering, yes you can bypass the internal AC power supply on an Xbox and run it straight off 12V! The main board has high voltage protection at about 12.5V, so you’ll need a buck/boost to produce a stable 12.0V. Still, probably an overall 5-10% efficiency boost from using an inverter! : To those wondering, yes you can bypass the internal AC power supply on an Xbox and run it straight off 12V! The main board has high voltage protection at about 12.5V, so you’ll need a buck/boost to produce a stable 12.0V.

Why is my Xbox brick not turning on?

If your original Xbox One console isn’t receiving power from your power supply unit, the unit may need to be reset : Unplug the power cables from the console, electrical outlet in the wall, and power supply. Wait 10 seconds. Important Be sure to wait 10 seconds.

What to do if power brick is not working?

Power Cycle the Console – Microsoft recommends you try power cycling your console if you ever run into issues with the power supply brick. This can soft reset the power supply, which might end up solving your issue. To power cycle the console:

1. Unplug the power cable that goes to your wall adapter or surge protector from your console.
2. Wait at least 15-20 seconds before plugging the cable back in.

After you plug the power cable back in, check if the flashing orange light appears again.

Are all Xbox 360 power bricks the same?

You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser, Joined May 15, 2007 Messages 4,459 How do we tell which power brick we need for our 360’s? I got a old xbox 360 from a friend that has rrod, He told me if i can fix it I can have it but it has no video or power brick (he’s not sure where they went as its been in his closet for a long time).

its mfg date is 2005-10-20, how do I figure out what modle power brick it needs? Joined Oct 6, 2008 Messages 6,621 How do we tell which power brick we need for our 360’s? I got a old xbox 360 from a friend that has rrod, He told me if i can fix it I can have it but it has no video or power brick (he’s not sure where they went as its been in his closet for a long time).

its mfg date is 2005-10-20, how do I figure out what modle power brick it needs? The easiest way is to look at how many amps the console is rated at, which is located near the barcode and manufacturer date at the back of the console. There should be three possibilities – 16.5 for the oldest, most RROD-prone “xenon/zephyr” 360 units, 14.2 for the “Falcon” units, and 12.1 for the “Jasper”: The other way to find out which power supply your model needs is by inspecting the console’s power socket. Each power supply type uses a slightly different socket. The pic below shows the differences that each model has in the power supply socket (ignore the pic’s mention of HDMI): So if you can find out how many amps your particular model is quoted to use, you should be able to find a corresponding power supply, and the above pic of the sockets should help you confirm that a particular power supply matches up with your model. If your model was built in 2005, it probably uses the 16.5-amp power supply. Joined Sep 29, 2001 Messages 20,034 look at the wattage on your xbox and buy one that matches or is higher. from what I remember, the original power brick will work on all revisions of 360 but the new bricks are lower wattage so will only plug into the lower wattage newer 360’s. Joined May 15, 2007 Messages 4,459 ok thanks guys, it is indead a 16.5a model.

How do I clean the inside of my power supply?

As soon as you open your case, you will probably see empty areas occupied by dust and other debris. This is normal and easy to clean. Ensure you are in a well-ventilated space and use compressed air to remove the largest chunks of dust from within the case first.

Certain areas like empty hard drive bays or bunches of cables can have significant dirt buildup. If you can, remove cable ties or empty drive bays to clean behind them more easily. While responsible for cooling your computer, fans are also the leading cause of dirt and dust entering your PC. Debris hitches a ride with cold intake air and attaches itself to fans and any other component it can touch.

Compressed air can usually remove most dirt from case fans. Holding the fan when you spray it with compressed air protects the fan’s bearings, preventing it from rotating faster than designed and damaging itself. Sometimes, compressed air may not be enough to get the job done.

That is where cotton swabs come in handy. Using a fresh cotton swab, carefully dislodge any dirt from the fans that the compressed air could not free. Once you have removed all significant dust buildup from the fans, hit the entire area with air again to remove the fallen dust that was just cleaned off the fan.

As mentioned before, the most crucial part of cleaning a power supply is removing and adequately cleaning the dust filter before attempting to clean the rest of the device. Most components of a power supply are concealed within the part, so there is little you can do besides cleaning the dust cover.

What is a T10 screwdriver?

Torx Tamper Proof Screwdrivers are used to install or remove Torx Tamper Proof screws. These screws are identified by their 6 lobe head with a central pin, which makes tampering with the fastener difficult, if not impossible without the matching bit. Torx screwdrivers in this selection are made of S2 modified steel for industry leading performance.

Drive Size: T10 Blade Length: 3-1/8″ Blade Material: Through Hardened S2 Steel Handle Length: 3-7/8″

How do you unscrew a Torx screw without a Torx screwdriver?

Download Article Download Article It happens often enough that you don’t have a screwdriver handy but really urgently need to remove a screw. Although using a screwdriver is the easiest and safest way to remove a screw, there are different methods that can be attempted if you cannot find a screwdriver or cannot find the correct type and size of screwdriver.

1. 1 Use this method when trying to remove a Phillips head screw without the proper screwdriver. Phillips head screws are those that have two grooves forming a cross. In some cases one of the grooves will be longer than the other; if one groove is longer, this is the groove you should use when trying to unscrew your screw because it is easier to use with a variety of improvised tools.
   • Phillips head screws are particularly prone to being stripped, when the corners formed by the grooves are worn. This makes it very difficult to unscrew your screw because there are no longer solid grooves in which to insert your tool. Be very careful when using these methods so as not to strip your screw.
2. 2 Find a kitchen butter knife. Kitchen butter knives can be used in a very similar way to coins. Insert the end of the butter knife into the longer groove and turn counterclockwise to unscrew the screw.
   • If your butter knife is of low quality and strength or the screw is very tight, then you may bend your butter knife rather than unscrewing the screw. Be aware of this potential damage.

   Advertisement

3. 3 Try a coin. Try inserting a small coin into the longer groove and seeing if it will turn the screw. Dimes and pennies are particularly useful for this method. This will usually only work for larger sized screws rather than very small ones.
   • Insert the coin into the larger groove and turn counterclockwise.
4. 4 Try pliers or vice grips. This will only work if the head of the screw is somewhat raised above the surrounding surface. Use the pliers or vice grips to grab the sides of the screw head and turn the screw counterclockwise to twist it out.
   • Needle nose pliers may work better than regular pliers.
5. 5 Use your thumbnail. Your thumbnail will only work if the screw is quite loose in the surface. Insert your nail into the longer groove and turn counterclockwise. If the screw is relatively loose then the screw should come out easily but if it is tight then this method likely will not work.
6. 6 Use an old CD. Insert the edge of an old CD into the longer groove and turn counterclockwise. This can damage and/or break the CD so make sure to use an old one that you don’t mind damaging.
   • If the screw is very tight then this method might not work very well.
7. 7 Use a hacksaw to create a long groove in the screw, similar to a flat head screw. If your screw head is raised above the surface, you can use a hacksaw to create a groove similar to that of a flat head screw. Hold the hacksaw vertically and slowly cut the end of the screw to create a groove.
   • Make sure you do not cut the surface of the wood or whatever the screw is fastened to.
   • Remove the screw as you would a flat head screw, such as with a flat head screwdriver or another flat object such as a credit card.
8. 8 Use a flat head screwdriver. If you can’t find your Phillips head screwdriver but can find a flat head screwdriver, try using a flat head that is about the same length as the longer groove in the Phillips head screw. Insert the flat head into the longer groove and turn counterclockwise to unscrew.
   • This will not work with smaller screws, but it should be fine for normal size and larger screws.
   • Be careful not to damage your screw because there will now be less surface area in contact with the screw head.
9. 9 Try a plastic toothbrush. Take a plastic toothbrush and lightly melt the end using a lighter or other source of heat. Once the plastic is soft you can insert it in the head of the screw and allow the plastic to harden once more. Once it is hard try to turn the screw counterclockwise to unscrew it.
   • This will usually only work with screws that are not too tight and relatively easy to turn.
   • Be very careful when using the lighter to avoid accidents and make sure to melt the toothbrush slowly so you can monitor the melting and prevent a mess from the melting plastic.

Advertisement

1. 1 Use this method to remove a flat head screw without a screwdriver. A flat head screw has one groove across the head of the screw only. If you do not have a flat head screwdriver then you can usually use any kind of flat surface to unscrew the screw.
2. 2 Use a card. Try using a card such as a plastic credit card to turn the screw. Insert the edge of the card into the long groove and turn counterclockwise to unscrew the screw. Make sure the card is strong and old as it could be damaged in the process.
3. 3 Try the tab from a can of soda. Remove the tab from a can of soda and insert into the groove on the head of the flat head screw. Turn the head counterclockwise to unscrew the screw.
4. 4 Try a coin. Try inserting a small coin into the groove and turning counterclockwise to unscrew. Dimes and pennies are particularly useful for this method but larger coins will be easier to turn if they fit in the groove.
5. 5 Find a kitchen butter knife. Kitchen butter knives can be used in a very similar way to coins. Insert the end of the butter knife into the groove and turn counterclockwise to unscrew the screw.
   • If your butter knife is of low quality and strength or the screw is very tight, then you may bend your butter knife rather than unscrewing the screw. Be aware of this potential damage.
6. 6 Try pliers or vice grips. This will only work if the head of the screw is raised above the surrounding surface somewhat. Use the pliers or vice grips to grab the sides of the screw head and turn the screw counterclockwise to twist it out.
   • Needle nose pliers may work better than regular pliers.
7. 7 Use your thumbnail. Your thumbnail will only work if the screw is quite loose in the surface. Insert your nail into the groove and turn counterclockwise. If the screw is relatively loose then the screw should come out easily but if it is tight then this method likely will not work.

Advertisement

1. 1 Use this method if you have a torx screw. Torx screws have a star-shaped pattern on the head and are very popular screws for all purposes. Security torx screws will have a nub in the middle of the screw head that needs to be accounted for.
   • Torx screws can be easy to damage so be very careful when using an alternative tool to unscrew these screws.
2. 2 Use a small flat head screwdriver. Insert the flat head screwdriver between two opposite edges of the screw head. Turn counterclockwise to remove the screw. Make sure you turn slowly so as not to damage the head.
   • For security torx screws you will need to insert the flat head in against one of the outer grooves and the center nub of the head. This works much the same as non-security torx screws.
   • Security torx screws will usually turn the opposite direction, so you should turn clockwise to remove them.
3. 3 Break out the pin on security torx screws. If you have a normal torx screwdriver but not a security version then you can simply remove the center pin out of the screw head. Take a hammer and a punch or other chisel-like tool and line up the chisel at the bottom of the pin. Gently tap on the top of the chisel to remove the center pin.
4. 4 Drill a small hole in the tip of your torx driver. If you have a security torx screw and wish to remove using a non-security torx driver or drill bit then you can drill a small hole in the drill bit. This way it has a small hole to accommodate the center pin on your security torx screw.
5. 5 Try a plastic toothbrush. Take a plastic toothbrush and lightly melt the end using a lighter or other source of heat. Once the plastic is soft you can insert it in the head of the screw and allow the plastic to harden once more. Once it is hard try to turn the screw counterclockwise to unscrew it.

Advertisement

1. 1 Use this method for removing very tiny screws without a screwdriver. Very tiny screws are particularly difficult to remove without the proper tools. They are often found on electronics devices. If you can, use an eyeglass repair kit to remove your screws, which will have the necessary tiny screwdrivers.
   • If you cannot find or use an eyeglass repair kit then you can try one of these methods.
   • Eyeglass repair kits are very cheap and easy to find.
2. 2 Try the tip of a knife. Use the pointed tip of a knife to turn tiny screws counterclockwise. Insert the knife tip into the groove; if you can, try inserting the knife tip at a slight angle to provide more contact surface area between the knife and the screw.
3. 3 Use a metal nail file. Use the tip of a metal nail file to insert into the groove on the top of the screw head. Turn the screw counterclockwise, being careful not to damage the head.
4. 4 Use the tip of pointy little scissors. Insert the tip of very pointy scissors into one of the grooves on the screw head. Turn the screw counterclockwise.
   • Blunt scissors will not work well for opening very small screws.
5. 5 Try the tip of tweezers. Insert the pointy tip of tweezers into the groove on the screw head and turn counterclockwise. The tip of tweezers must be pointy to be inserted into the groove properly.

Advertisement

Add New Question

• Question If I use it without a screwdriver how do I screw it back in again? Use anything listed in the article to screw it back in.
• Question What can I use to unscrew a screw in my phone? Perhaps a small-sized Phillips, a small torx or possibly a pentalobe screwdriver. You’ll need to determine what type is needed for your phone.
• Question What do I do if the screw is too small? You will need to find a larger one.

See more answers Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit Advertisement

• Try spraying a little WD-40 on the screw before attempting to remove it. This might help loosen the screw and make it easier to remove
• For unusual screws such as those in electronics devices you may need to acquire a specialist tool as attempting to undo these without the correct tool may either invalidate the warranty or damage the screw to a degree where it will not be able to be removed without drilling it out.
• Remember that a shop purchased screwdriver will always perform better than any adapted method. Always try to use a screwdriver where possible that is designed to remove the screw.

Show More Tips Thanks for submitting a tip for review! Advertisement

• Take care when using knives or improvised devices to remove screws as these can be dangerous to use in a manner with which they were not designed.
• Always use power tools appropriately and be careful to keep moving parts away from your body to prevent injury. Follow all safety precautions recommended by the manufacturer.
• Always be careful when using a lighter to melt the toothbrush. Keep flame away from body parts and any flammable objects to prevent a potential fire.
• Using inappropriate tools to unscrew screws may invalidate the warranty on certain electronic devices.

Advertisement Article Summary X To unscrew a Phillips or flathead screw without a screwdriver, you may be able to use common household items. For instance, try inserting the edge of a coin, the tip of a butterknife, or even your thumbnail into one of the grooves at the top of the screw.

Use the flat edge of the object to turn the screw counterclockwise and loosen it, just like you would with a regular screwdriver. If you don’t have anything that can fit in the grooves on the screw, grip the top of the screw with a pair of pliers or vice grips, then turn it counterclockwise until it’s loose.

This technique will only work if the top of the screw sticks up enough so you can get a good grip on it. If all else fails, use a hacksaw to cut a larger groove into the top of the screw. This will make it easier to fit a flat edge into it so you can loosen it.

1. For extra tiny screws, use a pointed object, like the tip of a sharp knife or a nail file.
2. You can also try using the tip of a pair of a small pair of scissors or tweezers.
3. Unscrewing a torx screw, or a screw with a star-shaped hole, can be trickier.
4. You may be able to fit a small flathead screwdriver into the top of the torx screw.

If you don’t have any kind of screwdriver, use a lighter to soften the plastic at the handle end of an old toothbrush. Insert the softened plastic into the top of the screw so it molds to the shape of the hole. Once the plastic cools and hardens, turn it to loosen the screw.

Will a Xbox 360 power brick work on a Xbox One?

Will my xbox 360 psu work with an Xbox one s?

HiIt is not possible to use and Xbox 360 power supply on any Xbox One Consoles however as you are purchasing an Xbox One S I believe the internal power supply is multi voltage and all you will require is an new power cable.Please be aware from a general support point of view it is always best to purchase the console in the country/region you are intending to use it.

Type of abuse Harassment or threats Inappropriate/Adult content Nudity Profanity Software piracy SPAM/Advertising Virus/Spyware/Malware danger Other Term of Use or Code of Conduct violation Child exploitation or abuse Harassment is any behavior intended to disturb or upset a person or group of people.

• Threats include any threat of suicide, violence, or harm to another.
• Any content of an adult theme or inappropriate to a community web site.
• Any image, link, or discussion of nudity.
• Any behavior that is insulting, rude, vulgar, desecrating, or showing disrespect.
• Any behavior that appears to violate End user license agreements, including providing product keys or links to pirated software.

Unsolicited bulk mail or bulk advertising. Any link to or advocacy of virus, spyware, malware, or phishing sites. Any other inappropriate content or behavior as defined by the Terms of Use or Code of Conduct. Any image, link, or discussion related to child pornography, child nudity, or other child abuse or exploitation. Yes No Great! Thanks for your feedback. How satisfied are you with this reply? Thanks for your feedback, it helps us improve the site. How satisfied are you with this reply? Thanks for your feedback. : Will my xbox 360 psu work with an Xbox one s?

What color should the Xbox 360 power brick be?

Check the light on your power supply Solid green or solid orange light : Your power supply is working. If your console won’t turn on, try our Xbox 360 No Power Solution. Flashing orange, solid red, or no light: Your power supply may need to be replaced.

What is the GREY wire in Xbox 360 power supply?

Power supply reverse engineering – The Xbox 360 power supply provides two voltage rail : 5V and 12V. Most of the available power is on the 12V rail. As mentioned, the power supply uses a proprietary connector as shown below. Xbox 360 Slim power supply connector The connector consists of two barrel connectors.

Cable color	Pin	Use
Black / Grey	outer rings	ground
Yellow	inner rings	+12V
Red	left pin	+5V
Blue	right pin	12V enable

By default, only the 5V rail is enabled. To enable the 12V rail, 5V must be applied to the “12V enable” wire (blue). When this wire is enabled, the LED on the power supply turns green. There seems to be a pull down resistor inside the power supply on the “12V enable” wire, so it should be safe to apply directly the 5V to the cable.

How do you take apart a Xbox One shell?

1. 1 Make sure you have the necessary equipment. To disassemble your Xbox One, you will need the following items:
   • Flathead screwdriver (substitute plastic tool if possible)
   • T8 Torx screwdriver
   • T9 Torx screwdriver
   • T10 Torx screwdriver
   • Plastic prying tool (optional, but recommended)
2. 2 Disconnect your Xbox One from all sources. Your Xbox One should be completely free of any wires or attachments, including external storage, HDMI/audio cables, and the charging cable. Advertisement
3. 3 Ground yourself before taking apart your console. Static electricity can permanently damage circuitry, so make sure you practice proper grounding techniques like touching a metal surface before working.
4. 4 Remove the left-hand side panel. Insert a flathead screwdriver or spudger into the space between the back-left corner of the console and the plastic grille on the left side of the console, then gently pry the grille away from the console.
   • It helps to use a plastic tool rather than a metal tool here, since the grille is made of relatively delicate plastic.
5. 5 Slide the casing bracket off of the console. The casing bracket is on the far-right side of the grille area. Slide this left until it pulls away from the console.
6. 6 Unhook the second bracket. It’s on the far-left side of the grille area. To unhook this bracket: pull on the bottom of the bracket while pushing on the top of the bracket, then insert a flathead screwdriver into the seam that’s covered by the warranty sticker on the back of the console and pry until the bracket unhooks.
   • This is easiest if the console is upright.
   • Breaking the warranty sticker will officially void your warranty.
7. 7 Detach the rest of the casing brackets. Insert your screwdriver into the top section of the grille that’s on the back of the console and twist it until the bracket unhooks, then repeat this process all the way down the side of the console. Once all of the brackets are unhooked, the back part of the Xbox One’s casing will pop open.
   • Do not pull the casing off of the console yet. Doing so will break the ribbon that connects the front of your Xbox One to the circuit board.
8. 8 Swing the top of the casing up. Make sure the Xbox One is sitting flat with its bottom face-down when you do this. The top of the casing should swing up and over, coming to rest at a 90 degree angle to the console’s body.
9. 9 Unplug the front panel ribbon cable. Find the front of the cable, which will be near the “On” button for the console’s face plate. Once you find it, pull the blue tab that’s wrapped around the connector up, then gently tug the cable to the left. This will disconnect the cable from the top of the casing.
10. 10 Pull the top of the casing away from the Xbox One’s body. You should be able to do this without any resistance, since all of the connectors are now unhooked.
    • Set the casing aside in a safe, dry place.
11. 11 Disconnect the speaker and Wi-Fi wires. There should be two wires connecting the top of the console to the front of the console; unplug these from the front of the console by gently pulling on them.
12. 12 Unscrew the Wi-Fi card. Use a Torx T8 screwdriver to do this. The Wi-Fi card is in the lower-left corner of the Xbox One’s casing if the front of the Xbox One is facing you.
13. 13 Remove the Wi-Fi card. Pull the card straight up from underneath. This will unplug the Wi-Fi card from the Xbox One’s internal circuit board.
    • Set the Wi-Fi card aside in the same place as the top of the Xbox One’s casing.
14. 14 Remove the screws from the metal case. Use your T9 and T10 Torx screwdrivers for this. The metal case is the last piece of the Xbox One that you need to remove in order to open it. There are eight total screws to remove; you’ll see a light “C” with a number next to or below the screws.
    • Two of the screws are at the bottom of the fan box.
    • Make sure you place the discarded screws in a plastic bag so that you don’t lose them.
15. 15 Gently open the metal case. Hold the fan corner of the case and pry it up diagonally so that the cable in the adjacent corner isn’t damaged.
    • Don’t force this step. If you feel resistance at any point, set the case down and try again.
16. 16 Unplug the cable. This is the cable that attaches the Wi-Fi card to the console’s circuitry. Gently tug the cable’s connector, which is white, away from the off-white port into which it’s plugged. This will completely detach the top of the metal case from the Xbox One.
    • Set the metal case aside with the cable side facing up.
17. 17 Review your Xbox One’s internal parts. You should be able to see the fan, the hard drive, and the CD drive, as well as the green motherboard along the bottom of the console.
    • The whole bottom part of the Xbox One’s casing is now removable as well. This is helpful if you want to paint or otherwise detail your Xbox One’s casing.
    • If you want to remove a stuck CD from your Xbox One’s disk drive, there should be a pinhole in the front of the Xbox One’s face plate where you can insert a small item (e.g., a paperclip) to force the drive to open.

Advertisement

Add New Question

• Question Could this cause any damage to the Xbox One? It shouldn’t, because anything you remove, you can simply put back in. It may void your warranty, however.
• Question How do I fix my Xbox One if it automatically turns off whilst I am still playing? The Xbox may not be getting enough air circulation for cooling and is shutting down when it gets too hot. Make sure there is ample ventilation for the Xbox, and make sure nothing is covering the vents on the top right of the box. Even something small like a disc case makes the difference.
• Question If my warranty is voided, is it illegal to open my Xbox One? If the XBox is your property, it is never illegal to open it, the only risk is voiding your warranty. If you have already voided your warranty, you have nothing to worry about.

See more answers Ask a Question 200 characters left Include your email address to get a message when this question is answered. Submit Advertisement

• Be aware that any wrong mistake can lead to electrocution
• Only open your Xbox One if you know exactly what you want to do with it. Opening your Xbox One for curiosity’s sake will only serve to void your warranty; there are plenty of Xbox One tear-down videos available if you want to see the internal components without harming your own console.

Thanks for submitting a tip for review! Advertisement

Opening your Xbox One while it is plugged into a power source may result in electrocution.

Advertisement Thanks to all authors for creating a page that has been read 387,709 times.

How do I fix the orange power brick on my Xbox One?

The Orange light on your Xbox One power brick means that the power supply has run into an issue. To fix this, power cycle the console or reset the power supply.